Replacement Grease Cap Rubber Insert For EZ Lube Grease Caps

Question

Question:

Need just the rubber cap that goes in dexter easy lube hub. Is that possible? Thank you

asked by: Doc V

0

Expert Reply:

The Grease Cap Plug for E-Z Lube Grease Caps # RG04-010 will replace your missing rubber cap on your Dexter E-Z lube axle hub.

expert reply by: Bud M

0

Answer 1

The part #RG04-010 is designed to fit a 1.18 inch grease cap center hole. If you measure yours and it matches that then these are the correct ones. It's hard to say if the amount of play you mentioned is acceptable but you do want to them to seal…

view full answer...

Answer 2

Because the zerk fitting is a press fit, if they are falling out I would recommend simply leaving them out and replacing your existing grease caps with bearing protectors like Bearing Buddies. The Bearing Buddies you need will depend on your hub…

view full answer...

Answer 3

The center portion of the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 is designed to allow the grease to expand slightly when warm and not pop the cap off. If you are seeing it pop out when cold you may have too much grease in the hub. I'd…

view full answer...

Answer 4

The #RG04-010 are designed for use on EZ Lube spindles and hubs, which it sounds like what you're referring to with the grease zerk at the center of the hub. It might be a close fit with the cap, but as long as everything is seated properly on…

view full answer...

Answer 5

We do not carry the Tie Down Engineering hubs and caps, so I could not check for sure if they would fit the Tie Down Super Lube grease caps. I did get the measurements for the plugs and they will fit a 1-1/4 inch opening on a grease cap. If the…

view full answer...

Answer 6

The part you were looking at, Redline part #RG04-010 is designed to replace the caps on Dexter EZ Lube axles. If your trailer has Dexter EZ Lube axles this part will fit.

view full answer...

Answer 7

The Grease Cap Plug for E-Z Lube Grease Caps, #RG04-010, is designed to fit Dexter E-Z Lube grease caps on the Dexter E-Z Lube axles like #RG04-040, and will otherwise fit a 1-1/4 inch opening on a grease cap. The Rubber Lube Plug - Fits 1.18 Inch…

view full answer...

Answer 8

I checked your order notes and the leaf springs you bought last year were the part #e28SR which are for 5k axles. Since this is over the capacity of your axle failure would not have been caused by over loading the trailer assuming you stayed under…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Replacement Grease Cap Rubber Insert For EZ Lube Grease Caps

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching