Can RackEm Trailer Dolly be Used to Move a Pop-Up Camper that Uses a 2 Inch Ball

Question

Question:

Can i use a trailer dolly RA20 to move a pop-up camper that requies a 2 ball? The RA20 only comes with a 1 7/8 ball. Thanks!

asked by: Gregory

0

Expert Reply:

You can use the trailer dolly, part #RA20, to move the pop-up camper that uses any size ball. Proper ball fit is necessary when towing, but for moving a trailer with this dolly it is not necessary.

expert reply by: Heather A

0

Answer 1

If your trailer has a 2-inch ball coupler you can still use the 1-7/8-inch Rack'Em Trailer Dolly #RA20 to move it to and from your storage position. While it would not be appropriate to tow with different sizes of ball and coupler use of a tow…

view full answer...

Answer 2

The Rackem Trailer Dolly, #RA20, only comes with a 1-7/8 inch ball. A 2 inch ball is not available for this item. Proper ball fit is necessary when towing, but it is not necessary when moving a trailer with this dolly. This dolly can even be used…

view full answer...

Answer 3

You can't get a larger ball for the Rack'Em Trailer Dolly part #RA20, but the good news is that you don't need one to use it with a trailer trailer that has a coupler designed for a 2-5/16 inch hitch ball. The reason for this is that the…

view full answer...

Answer 4

I spoke with my contact at Draw-Tite and he informed me that this Draw-Tite #75237 should work on your 2016 Toyota Sienna SE. I asked about the lower trim piece that the SE models have on them and he informed that there will be an appearance panel…

view full answer...

Answer 5

For your situation the easiest dolly solution we have is the Trailer Valet XL part #TVXL2. This attaches to the coupler ball and gives you an easy to turn crank which turns the wheels of the dolly allowing it to easily be moved. Standard dollies will…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Can RackEm Trailer Dolly be Used to Move a Pop-Up Camper that Uses a 2 Inch Ball

Product Page this Question was Asked From

Continue Researching