Length and Diameter of Yakima Threaded Hitch Bolt

Question

Question:

What sizelength and Diameter is the hitch bolt for the 2inch adapter for the Yakima Stick up. We only have the 11/4inch hitch bolt and its too short. Thank you

asked by: Kevin

0

Expert Reply:

The Yakima Threaded Hitch Bolt, part # Y8890200 is 5/8 inch in diameter and a 4-1/4 inch overall length, as shown in the provided photo.

The StickUp originally included two different hitch bolts, one for the 2 inch hitch and a shorter one for the 1-1/4 inch. The # Y8890200 is intended for use in the 2 inch hitch.

expert reply by: Mike L

0

click to enlarge

Answer 1

I believe you are asking for the replacement hitch bolt for your Yakima BackSwing Swing Away Hitch Extender #Y02483, which is something that we do carry: - Replacement Hitch Bolt, Nut and Clip #Y8780022 I did verify for you with Yakima that this is…

view full answer...

Answer 2

The Yakima HitchLock for Yakima Hitch Mounted Bike Racks - Same Key System (SKS) #Y07235 is the lock you are seeking. It is designed to work with the Replacement Hitch Bolt, Nut and Clip for Yakima Bike Racks and DryDock Load Assist - 2"…

view full answer...

Answer 3

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 4

Both of the bolts that come with the Yakima Hitch Pin Set #Y8880131 are 1/2 inch diameter with 13 threads per inch. One is 4.279” long and the other is 2.598” long.

view full answer...

Answer 5

I have actually seen this issue before since the 2 inch receivers on Toyota trucks and SUVs have a slightly larger diameter on the outside of the receiver tube than most typical 2 inch hitches; it's partially the powder coating but the steel…

view full answer...

Answer 6

Yakima Mounting bolt #Y8890176 is a 1/2 inch bolt, which measures 4-9/16 inches long. This bolt works with the following bike carriers: Yakima FlipSide (Y02426), DoubleDown 2 (Y02423), DoubleDown 4 (Y02424), DoubleDown 5 (Y02425) BigHorn 4 (Y02405),…

view full answer...

Answer 7

The part #Y8890200 is 4-1/2 inches long which may be longer than what you currently have since some of the pins are only 4 inches long.

view full answer...

Answer 8

We do have what you need but I checked with Yakima for you and the part you mentioned will not work with a Yakima FourTimer bike rack. Instead, there are a couple of parts you that you need, and I verified this with Yakima for you: - Replacement…

view full answer...

Answer 9

I went and pulled a Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier #Y8890200 from our warehouse to measure and found that the bolt has 5/8 inch coarse threads and the size wrench you would need to use to tighten it would…

view full answer...

Answer 10

Without knowing what bike rack you have it's hard to say what pin you would have currently, but I did speak to my contact at Yakima and she said that the part #Y8890200 is 4-1/2 inches long which may be longer than what you currently have since…

view full answer...

Answer 11

I spoke with Yakima and they informed me that the part you are looking for has been discontinued and is no longer available for purchase. There is also not a direct replacement either but they did say the Replacement Hitch Bolt and Clip for Yakima…

view full answer...

Answer 12

I went out into our warehouse and measured the threads of the Replacement Threaded Hitch Pin and Clip #P5902 and found them to be 1/2 inch diameter coarse thread. The version of this bolt that is designed for 2 inch hitches is the Swagman Threaded…

view full answer...

Length and Diameter of Yakima Threaded Hitch Bolt

Product Page this Question was Asked From

Continue Researching