6x4 Inch LED Trailer Tail Lights that Mount on Studs on 2 Inch Centers for Shorelander Boat Trailer

Question

Question:

I have a shorelander boat trailer. The present lights are 6inch wide x 4inch high and have two mounting studs on 2inch centers. Do you sell any waterproof LED lights that fall in the dimension range shown?Break, turn signal, light combination

asked by: Al B

0

Expert Reply:

We have Wesbar lights # 271585 for the left and # 271584 for the right. They are 6 by 4 inches, LED, waterproof, mount on studs on 2 inch centers, and you would need pigtail # 40-00-003 (one for each light).

LED tail light # STL56RB for the right hand side and # STL57RB for the left are a close match. They are 6-1/16 inches across and 3-5/8 inches tall. They mount on studs on 2 inch centers. The lights are submersible and the LED board sealed to keep out water.

expert reply by: Michael H

0

Answer 1

I looked up picture of your 2019 Shoreland'r SLR14TM boat trailer and while I wasn't able to get a really clear shot it looks like the trailer uses square taillights like the kit part #TLL160RK which would work great as they are submersible…

view full answer...

Answer 2

Most of the Haul Rite trailer lights will need to be replaced because they have a sealed housing to allow the lights to be submerged. There are some that do allow bulb replacement like the Wesbar #403026, but that has a very simple to access light…

view full answer...

Answer 3

First, the additional function is a license plate light. If your license plate is mounted and/or illuminated elsewhere then you could use 2 right side lights. When replacing trailer lights it is best to go with all LEDs or all incandescents. Mixing…

view full answer...

Answer 4

I attached a picture that shows what type of lighting requirements are needed for a trailer over 80 inches in width as well as a link down below that covers this as well.

view full answer...

Answer 5

Yes, the Optronics LED Combination Trailer Tail Lights item #TLL160RK are DOT compliant. They meet the Federal Motor Vehicle Safety Standard 108 (FMVSS 108) which regulates all automotive lighting, signaling and reflective devices in the United…

view full answer...

Answer 6

The two kits both have the same taillight but the part #TLL160RK only comes with the two light assemblies whereas the part #TLL16RK comes with additional wiring to from the front of the trailer to the rear as well as a license plate bracket.…

view full answer...

Answer 7

We do have an over 80 inch LED trailer taillight kit that's submersible and would work great on your 1998 Shorelandr boat trailer as the part #TL16RK. This comes with the LED taillights you want, clearance lights, license plate bracket and…

view full answer...

Answer 8

We have the replacement light you need with part #STL56RB but just the replacement lens you need is not available so this would be best option.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...