Over-Under Axle Conversion Kit for 2-3/8-Inch Trailer Axle

Question

Question:

Im looking for single axle travel trailer 83 shasta/ 2-3/8axle over under conversion kit.I like to lower at list 6,its to high for me.Thanks for yours advice.

asked by: Jan

0

Expert Reply:

For your 1983 Shasta single-axle travel trailer you have identified the correct over-under axle conversion kit to fit its 2-3/8-inch diameter. This kit will provide approximately half of your desired height drop since its effect will be a function of axle diameter, which is 2-3/8-inches. Your trailer must have double-eye springs, not slipper springs, in order to use an over-under kit.

expert reply by: Adam R

0

Answer 1

Yes the Dexter Trailer Suspension Over - Under Conversion Kit #K71-384-00 that you referenced will provide additional clearance for loading your ATVs on your single axle trailer. This kit is a bolt on kit but Dexter strongly recommends tack welding…

view full answer...

Answer 2

A 3500 lb axle will typically be 2-3/8 inches in diameter. If that's the case with your axle, you'd want to use the #K71-384-00 Over/Under conversion kit you referenced. This will allow you to swap the spring pack from under the axle to above…

view full answer...

Answer 3

The Dexter Trailer Springs Over-Under Conversion Kit, part #K71-384-00, you referenced is intended for one axle, so you are right that you would need to order a quantity of 2 for a tandem axle trailer.

view full answer...

Answer 4

Gong with a 4,000 pound axle isn't going to be your solution. Your best bet is either installing the Dexter Trailer Springs Over-Under Kit #K71-384-00 which will essential move your springs to be on top of the axle and give you more clearance.…

view full answer...

Answer 5

The Scissor Stabilizer Jack #TJSC-24, which also comes in a 2-pack #TJSCHD-24 and a 4-pack #TJSCHD-24-4, is a universal fit so you would need to double check our measurements to ensure they fit your travel trailer. When they are collapsed they…

view full answer...

Answer 6

The capacity of scissor jacks is based on the individual jack. For example, the Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 10,000 lbs - Qty 4 #TJSCHD-24-4 each have a 2,500 lb capacity, but since these come in a quantity of four, the…

view full answer...

Answer 7

When using an over/under conversion kit such as #K71-384-00 to add ground clearance to a trailer the amount of height gained will the diameter of the axle plus the thickness of the leaf spring stack at the axle. So for example if your axle is 2-3/8…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Answer 10

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Over-Under Axle Conversion Kit for 2-3/8-Inch Trailer Axle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching