Will The Curt Q25 Hitch Head Work With The Curt 5th Wheel Round Tube Slider C16020?

Question

Question:

Will curt q25 hitch head work with this?

asked by: Chandler

0

Expert Reply:

Hey Chandler. Yes, your Curt Q25 hitch head will indeed work with the Curt 5th Wheel Round Tube Slider for Ford Super Duty Towing Prep Package # C16020. Just keep in mind that the slider base is rated for 24,000 lbs instead of 25,000 lbs for the head. So, 24,000 lbs will be the max towing capacity for this setup.

expert reply by: Jesse M

0

Answer 1

If both middle jacks are not retracting or extending on your #LC675817, odds are one or more of the fuses is out. There is a fuse for each of the legs and if one of these is bad, it will definitely cause the legs not to work. This can be mounted just…

view full answer...

Answer 2

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 3

I measured the jaws and on both the Q25 #C16265 and the Q20 #C16130 the thickness of both is 1/2 inch. The differences are most obvious in the vertical load limit and the gross towing weight ratings. I reached out to my contact at Curt and the jaws…

view full answer...

Answer 4

The Curt 5th Wheel Trailer Hitches like part #C16521 have three sets of adjustment holes which are each spaced 2" apart on center. I am not sure how much additional space you will need to clear your tailgate but you can try to move the hitch…

view full answer...

Answer 5

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 is going to slide back 12" to provide more turning clearance and will sit 17" - 19" tall so it's not going to contact the tailgate.…

view full answer...

Answer 6

I called my contacts at both Reese and Demco and asked about the differences in the pucks for your 2016 F-250. It seems with an aftermarket gooseneck puck system like part #RP30126, there is a button bolt that holds the pucks to the rails under the…

view full answer...

Answer 7

I know turning clearance can be a problem with the Megacab models of the Ram trucks. We do not carry any automatic sliding hitches at this time, only manual slide hitches, but we often find that sliding fifth wheel hitches do not always cut it when…

view full answer...

Answer 8

The three 5th wheel hitches that you are inquiring about are the Curt Q24 5th Wheel Trailer Hitch - Dual Jaw - 24,000 lbs, part #C16245 Curt Q25 5th Wheel Trailer Hitch - Dual Jaw - 25,000 lbs, part #C16265 Curt A25 5th Wheel Trailer Hitch - Dual Jaw…

view full answer...

Answer 9

There isn't a wedge made for the Q Series of Curt hitches as you cannot use Sidewinder pin boxes with them due to the jaw design and head material. Instead, you can use a fixed hitch like Reese M5 5th Wheel Trailer Hitch - Single Jaw - 20,000 lbs…

view full answer...

Answer 10

There are a few reasons why you may be getting the "feature disabled" code with your Lippert Ground Control 3.0 #LC358590. If you were trying to initiate hitch recognition, the front of your coach may have been below level; you would need…

view full answer...

Answer 11

For your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System 6-Point Set #LC675817 it sounds like you have a standard error that can come from a battery being drained too far. It appears you need to reset your zero point so that your…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...