Recommended 5th Wheel King Pin Lock that Can Be Keyed Alike

Question

Question:

We have several trailers and I would like to know if we could get 10 of these keyed alike?

asked by: Elijah A

0

Expert Reply:

No, I am sorry you can not. The AMPLock King Pin Lock item # AMP27FR doesn't have an option to be keyed alike. The only king pin lock I do have that you can get keyed alike is the etrailer item # e98896. You'll need to order all 10 at the same time and select the keyed alike option in the drop down above add to cart.

expert reply by: Jerred H

0

Answer 1

Yes, you can use B&W Companion 5th Wheel Trailer Hitch w/ Slider - Dual Jaw - 20,000 lbs Item #BWRVK3400-5W on both a long bed truck and a short bed truck. On the long bed truck you just won't have to slide the hitch back (though you…

view full answer...

Answer 2

There is a way to to a fifth wheel trailer with your 2020 Ram 2500 that has the Ramboxes but you have to install a Sidewinder pin box on the trailer so that the pivot point is raised up high enough that there isn't interference between the…

view full answer...

Answer 3

The most durable and theft-proof lock I've tested is the AMPLock King Pin Lock for 5th Wheel Trailers part #AMP77FR. The lock itself is very thick, around 10 lbs and it's made of cast iron. It also has a unique key system which…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb…

view full answer...

Answer 5

Yes, as long as you're using a set of industry standard rails like the Curt Custom Fifth Wheel Installation Kit for Ram Truck #C16427-204 in your truck then you'll have no issues swapping over to the Curt PowerRide 5th Wheel Trailer…

view full answer...

Answer 6

If it is necessary to cut the rails, I suggest you place the top piece into the side rails and measure from the top to the point that matches your desired length. Please look at image number 2 and compare to your particular camper. Can you place…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To replace your 16K Reese Hitch #RP30047 head, you will want the Replacement Head for 16K Fifth Wheel #RP58146. If you want to replace the head and head support and handle, you will want #RP30047A which is rated for 16k.

view full answer...

Answer 9

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Recommended 5th Wheel King Pin Lock that Can Be Keyed Alike

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching