Grease Recommendation for Curt Q25 Fifth Wheel Hitch

Question

Question:

I have a Curt Q25 hitch. What grease do you recommend for this hitch?

asked by: Tim N

0

Expert Reply:

Hey Time, according to Curt the recommended grease for your Curt Q25 fifth wheel hitch is a high-pressure wheel bearing grease.

For this I recommend the LubriMatic Wheel Bearing Grease # L11465.

expert reply by: Jameson C

0

Answer 1

Yes you are correct the Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid #MA00-04751KSX is the right replacement and measures 18 1/8" long and 16 1/2" wide, which is the same measurements as your current MaxxFan Plus Roof Vent w/…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 10

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

Hey Scott, so the braking and hub components of a Dexter 3,500 lb axle made in 1999 would be the same as what's currently used so those components would transfer over. So a bare axle like the part #T3584F-EZ-8974 would work for you but you'd…

view full answer...

Grease Recommendation for Curt Q25 Fifth Wheel Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching