Parts Needed To Add Electric Drum Brakes To A Flatbed Utility Trailer
Question:
Hello, have a question regarding adding electric brakes to a 16ft flatbed utility trailer. It has twin 3500lb axles with 5 stud hub on 4 1/2 center. The vehicle which pulls it does have a factory Ford F150 electric brake controller onboard. What parts exactly would be needed to add electric brakes to rear axle? Thank you in advance for any info.
asked by: David C
Expert Reply:
Hi David,
To add brakes you'll first need to check the axles to see if there is a brake mounting flange. If not then you'll have to replace the axles in order to get one with a flange so that you can mount brake assemblies. If you do have them then you can use the etrailer Electric Trailer Brakes # AKEBRK-35-SA. These brake assemblies are self-adjusting so once you complete the initial brake bedding process you won't have to adjust the brakes again.
From there you'll need a hub/drum assembly for each brake assembly. The # AKHD-545-35-EZ-K will most likely be a fit but you'll want to doublecheck the bearing and grease seal combination you currently have in order to confirm they match. If you look at the face of the bearings and seals there should be a part number, if not then you can measure your spindle at points B, C, and D with a pair of calipers # PTW80157.
Next you'll need a 7-way cable # H20046, junction box # 3375601101, and breakaway battery # 3802346. All of the electrical wiring will run to this junction box and connect to your tow vehicle with the 7-way cable. The junction box has various posts to separate each function and keep things nice and organized. You'll have to run some 10 gauge wire # 10-1-1 from the brake controller output post in the junction box out to the brake assemblies for power. The assemblies will have two wires, one for power and the other to be grounded to the frame with a ring terminal. They aren't specific so you can use either.
Since you already have an OEM brake controller you shouldn't have to do anything to the tow vehicle after the trailer is up and running. I do recommend installing brakes on both axles though for better stopping power and because some states and even smaller municipalities will fine you for not having brake assemblies on both axles if you're over 3,000lbs.
Products Referenced in This Question
Trailer Wiring Junction Box - 7 Color Coded Terminals - ABS
- Accessories and Parts
- Trailer Wiring
- Junction Box
- Buyers Products
more information >
Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Side Load
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-axle
- Tandem-axle
- LED Tester
- 1 Amp Charger
- Battery Included
- 5 Ah
- Bright Way
more information >
etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- etrailer
more information >
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 6 - 10 Feet Long
- Plug and Lead
- 7 Round - Blade
- Hopkins
more information >
4" Carbon Fiber Digital Caliper
- Hand Tools
- Measuring and Layout Tools
- Digital Calipers
- Carbon Fiber
- Performance Tool
more information >
Product Page this Question was Asked From
etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Hitch Covers
- Misc Covers
- Plain
- Rubber
- Fits 2 Inch Hitch
- Standard
- Square
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: My Trailer Hitch Doesn't Fit
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Curt Hitch that Fits 2023 Toyota Crown Hybrid
- Article: Rooftop Cargo Carriers
- Article: Best Bike Racks for Electric Bikes
- Q&A: Recommended etrailer Hitch for a 2023 Subaru Outback Wilderness
- Article: Trailer Wiring Diagrams
- Q&A: What Hitch Do You Recommend for a 2024 Toyota RAV4?
- Q&A: Difference Between Curt & etrailer Trailer Hitches For 2024 Subaru Crosstrek Wilderness
- Q&A: Recommended Hitch for a 2024 Honda CR-V Hybrid
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
David C.
3/11/2024
Kevin, thank you for your response. Much appreciated. David