What Mounting Pattern do 5.2k to 7k etrailer Electric Trailer Brakes Fit
Question:
I have a home made trailer I bought 20 years ago. The brake on one side is gone. I would like to replace them but want to make sure these will mount. I have a 12” drum the center opening is 4”, the mounting studs are about 7” across and about 4 3/8” apart. I hope this make sense. Would you have a drawing of the brake assembly that I could check
asked by: William K
Expert Reply:
Hi William; it does make sense and what I can do for you is give you the mounting bolt pattern of the 5-brake flange for the 5.2k to 7k etrailer Electric Trailer Brakes # AKEBRK-7-SA.
I have added a diagram below with the measurements showing what the # AKEBRK-7-SA fits.
(click to enlarge)
Product Page this Question was Asked From
etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 12 x 2 Inch Drum
- 5200 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- etrailer
more information >
Continue Researching
- Article: Trailer Wiring Diagrams
- Article: Trailer Lighting Requirements
- Video: Optronics Trailer Lights - Tail Lights - STL178RFPB Review
- Q&A: Troubleshooting Weak Trailer Brakes that Are Adjusted Properly and Have Good Magnets
- Q&A: Do Hubs/Drums Need to be Replaced When Changing Braking Assemblies
- Search Results: trailer running lights
- Search Results: trailer tail light
- Search Results: a70gb
- Search Results: a45pb
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Q&A: How To Determine Correct Braking Assemblies for Tow Master Trailer with Unknown Axle Capacity
- Q&A: Determining Which Replacement Braking Assemblies Fit 2002 Keystone Tailgator 210RR
- Shop: GloLight LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 22 Diodes - Oval - Red Lens
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Topwind - 10" Lift - 5,000 lbs
- Shop: PVC Grommet for 6-1/2" Oval Trailer Tail Lights
- Shop: Optronics LED Trailer Clearance and Side Marker Light w/ Reflex Reflector - 6 Diodes - Amber Lens
- Shop: Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
- Shop: GloLight LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 22 Diodes - Oval - Red Lens
- Search Results: 12 trailer brakes
- Q&A: Axle Kits with Electric Brakes to Replace Mobile Home Axles
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Shop: Trailer Hitch
- Search Results: trailer jack
- Q&A: How to Wire Electric Brakes on a Tandem Axle Trailer
- Video: etrailer Electric Trailer Brake Kit Installation
- Shop: Trailer Wiring
- Search Results: trailer brakes
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Article: Most Popular Wheel Bearings
on Trailer Brakes
William K.
3/4/2024
The AKABRK-7-SA drawing you sent does not look like it will work. As the picture I sent the center hub opening is about 4”. Do you have any brake assembly that has a 4” opening on the center hub? This is a 12” drum. Thanks in advance