Alternative Mounting Option for a 7" Furrion Vision S Monitor

Question

Question:

Hello, I am looking for a wall mounting bracket for a furrion vision s7 monitor, to mount it inside the trailer. Furrion shows one in their ads, but I can’t seem to find one. There is a lippert part number 776466 i think might apply, but not sure. Can you help? Do you have one? Tom Daher

asked by: Tom D

0

Expert Reply:

Tom, It looks like that mounting bracket you're looking for has been discontinued because I wasn't able to find it through Lippert, I could only find it in a few places but they didn't have any stock.

However, if you have the Vision S monitor # FR47FR like it sounds like you do, then you can also use the Replacement Suction Cup Mount for Furrion Vision S 5" and 7" Monitors # FR79SR as an alternative mounting option.

expert reply by: Bryce D

0

Answer 1

The Furrion Vision S Monitors, like the 7" #FR47FR, don't have a replacement antenna which is a bit frustrating but it's how Furrion has chosen to design their system. If you're wanting to extend out the antenna then that's…

view full answer...

Answer 2

To my understanding the Furrion backup camera system has had a few different makes but for the current version, the Vision S that uses 7" monitor #FR47FR, only the Suction Cup Mount #FR79SR is compatible. An older version may have used a…

view full answer...

Answer 3

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 4

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 7

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 8

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Alternative Mounting Option for a 7" Furrion Vision S Monitor

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching