Bearing Buddy And Spindle Grease Seal For The AKIHUB-545-2-1K Idler Hub Assembly

Question

Question:

Looking to purchase Bearing Buddies and seals for a trailer that uses your hub assembly AKIHUB-545-2-1K. Can you please confirm the proper parts are: Bearing Buddy 1980A Spindle grease seal BB60001 Also, I see the stainless steel Bearing Buddies 1980A-SS are slightly less money than the non-stainless. Is there a reason I would NOT use the stainless? This trailer will be solely used on the highway, not a boat trailer. Thank you.

asked by: Ron B

0

Expert Reply:

It looks like you did your homework Ron, because the Bearing Buddy # BB1980A and the Spindle Grease Seal Set # BB60001 are indeed the proper parts for the # AKIHUB-545-2-1K idler hub assembly. This hub uses the # L44643 inner bearing, so the bearing buddies and seals you picked are sized perfectly.

I will not pretend to fully understand our pricing algorithms, but if the stainless bearing buddies # BB1980A-SS are currently on sale I would definitely go with those. The chrome has decent rust resistance, but stainless is always preferred and will hold up better over time than chrome. Absolutely no reason not to use stainless in this case.

expert reply by: Jesse M

0

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Bearing Buddy And Spindle Grease Seal For The AKIHUB-545-2-1K Idler Hub Assembly

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching