Easiest Plug and Play Brake Controller For a 2024 Jeep Grand Cherokee

Question

Question:

What is the easiest to install brake controller for my 2024 Jeep Grand Cherokee?

asked by: Heath

0

Expert Reply:

The Curt Echo Under-Dash Bluetooth Brake Controller # C27JR will provide you with one of the easiest installations as the Pigtail # C51446 will connect it to your factory wiring. And unlike other controllers there is no dash mounted controller or knob so everything simply gets secured under your dash. Then you will control the settings for it with your smart phone using the OneControl app.

expert reply by: Bud M

0

Jacob

3/28/2024

But where is the plug in the 2024 jeep grand Cherokee? I have the factory tow but can’t find where to plug it in.

Reply

Bud M.

3/29/2024

@Jacob The factory connector to plug in the brake controller is located behind the left side kick panel in the drivers compartment. The connector is going to be taped up to the harness.

Reply

Answer 1

Hey Jon, so in theory the inline Echo Mobile part #C51180 and the under dash part #C27JR should perform the same but we have found that the under dash version works a lot better so it would be the way to go. Overall performance and connectivity just…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 10

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 11

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 12

To add a hitch to your 2024 Jeep Grand Cherokee L, I recommend the Draw-Tite item #DT42GR. This hitch is custom fit and bolts to your Jeep with included hardware. This is a class III hitch with a 2" receiver. It has a 7,500 lbs towing capacity…

view full answer...