2024 Ford F-350 Super Duty Correct Timbren Kit Fitment

Question

Question:

Whats the correct Timbren kit for my 2024 F-350 Super Duty?

asked by: Jessie

0

Expert Reply:

The only Timbren kit that fits your 2024 Ford F-350 Super Duty is the Timbren Suspension Enhancement System # TFR350SDJ rated for 8,600 lbs.

Please note these are only designed to help support your OEM suspension, and it won't increase your load carrying capacity.

expert reply by: Jon G

0

Bruce

2/26/2024

Hi Jon, I have the correct kit as you listed above for the F350 superduty , which I just installed tonight. My concern is that there is approx 2 to 2-1/2” between the Timbren and the axle, unloaded. According to the directions and the installation video, this doesn’t seem right. Thoughts?

Reply

Jon G.

2/27/2024

@Bruce @Bruce Since the ideal spacing between the Timbren # TFR350SDJ rubber springs and the contact point should be 1/2" to 1-1/2" it sounds like you're needing to install 2 of the Timbren 1" Spacer # A25723-90AH00 on your F-350. Just a head up, you'll need to get longer M10 bolts locally so you can accommodate the larger spacing between the spring and the mounting bracket.

Reply

Answer 1

The unloaded picture of your Timbren setup installed on your truck is concerning. Does the truck seem to sit level from left to right? Was it ever in an accident by chance? Are any of the suspension components worn out? You really shouldn't…

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 3

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 4

Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for. For the front, you'll want the TorkLift Camper Tie-Downs #TL87CR (TorkLift P/N…

view full answer...

Answer 5

You'll need to do some slight measuring to ensure the fit of the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F95FV on your 4WD 2022 Ford F-350 FX4 dually. Just measure from the top of the rear axle to the top of the jounce…

view full answer...

Answer 6

Hey Chip, so we do have a set of Torklift camper tie downs that fit your 2024 Ford F-350 long bed with side steps and a factory hitch with the part number #TL87CR for the front set and part #TLF3008 for the rear set.

view full answer...

Answer 7

The F2032 you're looking for is under part #TL87CR on our website and would be the correct fit for your 2024 Ford F-350. For the rear tie-downs you'll need part #TLF3008. To complete the setup you can use the TorkLift AnchorGuard Derringer…

view full answer...

Answer 8

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 9

The proper extension for your setup would be the one that allows you to have clearance of your hitch mounted accessory and also allows you to still be able to pull the steps down. If the receiver tube sticks out past the camper too far then you will…

view full answer...

Answer 10

I have two options that will allow for you to extend the connection point between your truck and trailer. The best option for you will depending on the gross trailer weight (GTW) and tongue weight (TW) of your trailer. As long as the GTW and TW of…

view full answer...

Answer 11

According to TorkLift's fitment guide the TorkLift Talon Custom Frame-Mounted Camper Tie-Downs #TLF2021A you were looking at are compatible with any factory installed running boards, including ones that extend under the bed so these would be a…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

2024 Ford F-350 Super Duty Correct Timbren Kit Fitment

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching