Roof Rack Recommendation to Fit Pace Edwards UltraGroove on a 2024 Ford F-250 Super Duty

Question

Question:

I have the Pace Edwards PE36QJ on my 2024 F-250 Super Duty and I was wanting to get roof rack crossbars installed. I don't need a full on ladder rack. What kit should I get?

asked by: Bill M

0

Expert Reply:

I recommend pairing the Rhino-Rack Vortex Crossbar Kit # RRVA165B-RRRLT600 with the Pace Edwards UltraGroove # PE36QJ on your 2024 Ford F-250 Super Duty. This gives you a simple crossbar system rated for 220 lbs that mounts a few inches above your tonneau cover so you can carry more cargo without it sitting up higher above your truck bed.

expert reply by: Jon G

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The Rhino-Rack Vortex Crossbars for Retrax XR and Mountain Top EVO-M Tonneau Covers #RRVA165B-RRRLT600 hasn't been tested to fit with the t-slots for a Pace Edwards Ultragroove tonneau cover and confirmed to fit. That being said the only thing…

view full answer...

Answer 3

Since you likely won't have enough clearance for a winch that uses a standard rotating handle, a winch with a ratcheting handle like the #DL16003 would be your best bet. I'd recommend using a couple of U-bolts to attach the winch to the…

view full answer...

Answer 4

In order to add a roof rack to the Pace Edwards Tonneau Cover with Explorer Series Rails you'll need a fit kit, mounting feet, and crossbars. I have attached these parts for you below. Fit Kit part #THKIT3101 Mounting Feet part #TH460R Corssbars…

view full answer...

Answer 5

The Rhino-Rack Quick Mount Legs #RRRLT600 that you mentioned will attach directly to the channels of a Pace Edwards UltraGroove Tonneau that you mentioned. Then for a pair of 59 inch long crossbars we have the part #RRVA150S-2 and you'd be set.

view full answer...

Answer 6

I have a possible solution for you. First, though, I spoke with Rhino-Rack about this as we have not attempted this fitting. They, unfortunately, cannot guarantee that the Rhino-Rack Roof Rack for Thule and Yakima Tracks, part #Y01-140B-NT, will work…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 10

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 11

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...