Replacement Front Anchor Plates For Happijac Camper Tie-Downs on 2005 Chevy Silverado 3500

Question

Question:

I am looking for the front happijac anchor plates for a 2005 chev 3500 dually

asked by: Paul F

0

Expert Reply:

We do have the replacement front anchor plates for the Happijac camper tie-downs for your 2005 Chevy Silverado 3500, with the correct part being the following:

- Replacement Front Anchor Plates for HappiJac Truck-Mounted Camper Tie-Downs # LC182872

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 4

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 9

Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for. For the front, you'll want the TorkLift Camper Tie-Downs #TL87CR (TorkLift P/N…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The #TLC3205 you have now is only designed to work with the factory hitch. Whether it is the #DT45517, a Curt hitch, or even a TorkLift hitch you will need a different rear tie-down. The correct rear tie-down for a 2002 Silverado 2500 without a board…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Replacement Front Anchor Plates For Happijac Camper Tie-Downs on 2005 Chevy Silverado 3500

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching