Pintle Hook Recommendation for 20K Curt Mounting Plate

Question

Question:

What hook do you recommend?

asked by: Sean

0

Expert Reply:

I recommend using the Curt SecureLatch Pintle Hook # CU97FR with the Curt Pintle Hook Mounting Plate # C48349. I really like the SecureLatch because it's a quick and easy way to secure your lunette ring.

expert reply by: Jon G

0

Answer 1

The mounting kit that is recommended for use with the 60k Buyers Products Pintle Hook part #337PH30 is the part #3378530 but this is only the hardware to mount the hook and does not include a plate. The hook has a capacity that's higher than any…

view full answer...

Answer 2

The Ball Platform #C28KR for a Curt Rebellion XD #C57UR has a 1-1/4" diameter hole opening. We also have the Pintle Mount Attachment #C79FR which has a bolt pattern for mounting accessories like the Pintle #CU87FR. It could also be used with a…

view full answer...

Answer 3

I would recommend Dexter Torflex axles the highest for torsion axles. And then put Al Ko and Lippert at about the same in quality. I was searching around online and the common consensus among the trailering forums is that the Dexter axles are…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 10

The best air bag kit for your 2020 Ford F-250 Super Duty with a single rear wheel are the Firestone Ride-Rite Air Helper Springs because they are the strongest, most durable air bags on the market to provide you with optimal support for your…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

I recommend going with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL89DQ for hauling around an in-bed camper with your 2024 Ford F-350 Super Duty. I really like this kit because it has the higher 7,500 lb rating (which you don't…

view full answer...

Pintle Hook Recommendation for 20K Curt Mounting Plate

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching