Mounting Hardware Needed To Install Curt QuickPin No Latch A-Frame Trailer Coupler 25474 # C84DR

Question

Question:

Hello: Question about Curt EZ latch coupler 25474....for 50 degree mounting. An installer is asking me the dimensions of the bolts needed......especially the length of the bolts. Can you tell me complete specs of the bolts, etc. Thanks.

asked by: Steve S

0

Expert Reply:

The Curt QuickPin No Latch A-Frame Trailer Coupler 25474 # C84DR will require grade 5 hardware. It is recommended to use six 1/2" bolts, six 1/2" lock nuts and twelve 1/2" washers. This can obviously change depending on your exact frame dimensions. I have linked the installation instructions at the bottom of the page which you can show the installer as well.

expert reply by: Bud M

0

Answer 1

There is! To replace the standard pin and clip on the Curt QuickPin No Latch A-Frame Trailer Coupler #C84DR Curt actually recommend the Hitch Lock #C23025 which is what I recommend going with!

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design then the Demco A-Frame Trailer Coupler #DM16680-52 will…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts…

view full answer...

Answer 8

The play you are feeling/hearing is most likely between the hitch ball and the latch of the coupler. If you look under the coupler you can see an adjustment bolt that uses an Allen wrench that will allow you to tighten the latch and get rid of the…

view full answer...

Answer 9

The Curt QuickPin No Latch A-Frame Trailer Coupler 25474 #C84DR will require grade 5 hardware. It is recommended to use six 1/2" bolts, six 1/2" lock nuts and twelve 1/2" washers. This can obviously change depending on your exact frame…

view full answer...

Answer 10

Hi Larry, So we have a couple bumpers that may work, though each is 96 inches long. They can be cut to length though, and the difference is their width, as one is 3" wide and the other 4" wide to fit different size bumpers: - Pre-Drilled…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Yes, so long as you have a standard a-frame trailer you will be able to replace your current welded on coupler with the Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Zinc - 2-5/16" Ball - 21K item #DM13205-95. I have attached…

view full answer...

Mounting Hardware Needed To Install Curt QuickPin No Latch A-Frame Trailer Coupler 25474 # C84DR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching