Will Demco A-Frame Trailer Coupler DM16680-52 Fit 2015 Featherlite 3116 Trailer

Question

Question:

will this fit a 2015 featherlite 3116 trailer

asked by: John D

0

Expert Reply:

I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design then the Demco A-Frame Trailer Coupler # DM16680-52 will fit as a bolt-on replacement. I linked a photo of this coupler to show you the mounting hole spacing.

expert reply by: Adam R

0

click to enlarge

Answer 1

Yes, you can use the Trailer Coupler Lock part #e98888 to prevent the hitch ball from coming uncoupled from the Demco 50-Degree A-Frame Trailer Coupler part #DM16680-52. The lock will install in the pin hole directly below the latch which you can see…

view full answer...

Answer 2

The Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole item #DM13205-95 that you referenced will fit a standard a-frame trailer. This is a bolt on coupler so you won't have to borrow a welder. To install you will want to use 3/8 inch, grade 5…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

You could drill into the Bulldog #BD028463 and make it a bolt-on but that's not really ideal. We don't have the exact match in a bolt-on model. We do have part #BD44150WH301 for a bolt-on Bulldog coupler. It has a higher rating but the price…

view full answer...

Answer 5

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts per…

view full answer...

Answer 6

I walked out to our warehouse and pulled the Redline A-Frame Trailer Coupler #CA5100B. At the widest point inside the coupler measured approximately 9-1/4 inches, the narrowest approximately 2 inches and 8 inches between those points. Check out the…

view full answer...

Answer 7

Yes, you will be able to replace your stock coupler with the Demco 50-Degree A-Frame Trailer Coupler #DM13205-95 as long as you have a standard a-frame trailer. I attached a picture below of the dimensions below so you can see if it would work for…

view full answer...

Answer 8

It sounds like you're looking for a replacement a-frame coupler like #CA-5280-RB but in a silver-painted or zinc-plated finish. Please click on the link provided to see all bolt-on standard a-frame couplers for 2-5/16-inch balls. For the…

view full answer...

Answer 9

There is! To replace the standard pin and clip on the Curt QuickPin No Latch A-Frame Trailer Coupler #C84DR Curt actually recommend the Hitch Lock #C23025 which is what I recommend going with!

view full answer...

Answer 10

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

view full answer...

Answer 11

There really is no reason you couldn't bolt on the coupler part #CA-5100-Z but there isn't a recommended way to do so. Best option would be to drill several holes spaced evenly on the a-frame portion of the coupler to the trailer frame.…

view full answer...

Answer 12

Nearly all A-frame trailer have a 50 degree angle frame so when it comes time to replace the coupler it's actually not that hard to pick out a replacement since basically any A-frame coupler will fit. The coupler part #CA-5100-Z that you…

view full answer...

Will Demco A-Frame Trailer Coupler DM16680-52 Fit 2015 Featherlite 3116 Trailer

Product Page this Question was Asked From

Continue Researching