Are All Replacement Lock Cylinder # BL7023480 Keyed the Same

Question

Question:

Will all three be keyed the same? Thats what i need.

asked by: Kimo L

0

Expert Reply:

The part # BL7023480 is a blank lock core and wouldn't be keyed to anything until you use your key in it. If you bought several and all used the same key to code them they all would be keyed the same.

expert reply by: Jameson C

0

Answer 1

I can help you find the right replacement lock cylinder for your 2007 Chevy Avalanche LT Toolbox. If your current lock cylinder can be removed from your Avalanche's toolbox then you will need the Late Model GM Key Cylinder from BOLT…

view full answer...

Answer 2

The Bolt Lock Core part #BL7023480 is compatible with the key of a 2015 Chevy as long as it looks like the key in the picture. How this works is that when you receive the lock core it is "blank". You will put your key in the core…

view full answer...

Answer 3

The Replacement Lock Cylinder for BOLT Toolbox Latch part #BL692915 is what you are looking for as it fits a 2007-2013 Chevy Silverado.

view full answer...

Answer 4

It sounds like you are looking for the Replacement Lock Cylinder for BOLT Toolbox Latch #BL7023482 which can key to the double side cut style key on your 2019 Toyota Tundra. We also have the following BOLT locks which you can code to your key. BOLT…

view full answer...

Answer 5

A 2016 Chevy Colorado should have a center cut transponder key so you would need the Replacement Lock Cylinder for BOLT Toolbox Latch - Codes to Center Cut GM Key #BL7023480. This is just the replacement lock cylinder so if you're needing parts…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Are All Replacement Lock Cylinder # BL7023480 Keyed the Same

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching