Correct Replacement For A MaxxFan 00-04951KSCX

Question

Question:

Do you have this model fan, if so, how much? 00-04951KSCX

asked by: Debbi

0

Expert Reply:

I am afraid we do not carry the exact model fan 00-04951KSCX that you are looking for. We do have the MaxxAir # MA00-04751KSX which is a very similar MaxxFan Plus Roof Vent. This will be a suitable replacement for your vent, if you are looking to replace it.

expert reply by: Jesse M

0

Answer 1

For your Maxxair Model 4951KSC, you can use the MaxxAir FanMate RV and Trailer Roof Vent Cover #MA00-955002. Even though this cover only has 10-1/4" of interior height, your MaxxFan will sense the cover when auto-opening, and stop opening, that…

view full answer...

Answer 2

You are correct that Atwood was bought out by Lippert, and replacement parts are difficult to come by these days. I spoke to my contact at Lippert and your Atwood 66280 Level Leg system does not have any replacement parts available, so the…

view full answer...

Answer 3

We sure do! The correct replacement slide out motor for your Power Gear 1510000042 is part #LC88UD on our site.

view full answer...

Answer 4

The switch on your wall is only turning the power on and off for the fan. With a powered lift there wouldn't really be a way to tap into the function and wire it to a switch to make it easier to access. The only option would be to replace the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 8

Good morning, Don. The 3/4" wide butyl tape is exactly what we recommend for installing a roof vent such as the MaxxFan #MA00-07000K. We actually sell a roof vent install kit part #344270KITW that comes with sealant, screws and a 30' roll of…

view full answer...

Answer 9

Actually the type of roof vent cover you need to attach to the vent cover brackets of your Maxxair 4951KS like part #MA00-04500K is the part #MA00-955003 which uses those brackets with the included cotter pins of the cover.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Correct Replacement For A MaxxFan 00-04951KSCX

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching