Which Blue Ox Trailer Hitch Receiver Immobilizer Fits a 2 Inch Trailer Hitch

Question

Question:

Is this the right unit for a 2inch ID RV receiver? I wasnt sure if the spec is based on ID or OD of the receiver. Thanks

asked by: Bill T

0

Expert Reply:

The 2 inch reference for the Blue Ox Immobilizer # BX88224 is in reference to the receiver opening, not the outside width of the receiver. For a 2 inch receiver opening # BX88224 is the correct option.

expert reply by: Michael H

0

Answer 1

You will need to go by the overall dimensions of the generator with the wheel kit on compared to the useable space on the TorkLift Lock and Load cargo tray #TLA7752. The tray itself is 27-3/4 inches long by 24 inches wide. The strap adjustment…

view full answer...

Answer 2

Yes you can use an adapter like the Brophy Trailer Hitch Receiver Adapter - 1-1/4" to 2" Hitch #HTAD to adapt your hitch over for use with the 24x27 TorkLift Lock and Load Maximum Security Cargo Tray for 2" Hitches 500 lbs…

view full answer...

Answer 3

The 24x27 TorkLift Lock and Load Maximum Security Cargo Tray #TLA7752 that you referenced is rated for the rougher ride quality that is present at the rear of travel trailers like yours which is a bit rougher like you noticed. I attached a picture…

view full answer...

Answer 4

It looks like there are a couple of different Honda 3000 generators. Based on the length, width, and height of those you could use the TorkLift Lock and Load carrier #TLA7752. The tray measures 27-3/4 inches by 24 inches. I have linked a video…

view full answer...

Answer 5

Since generators are so heavy I do not recommend mounting it on the rear bumper of your Jayco travel trailer. What I recommend is to install a frame mounted hitch at the back of the trailer which will be a stronger and safer connection point. We…

view full answer...

Answer 6

Best option for locking generators to the Stromberg Carlson part #CC-255 will be a cable lock like the #e98891 which you could route through the handles of the generators and then around the platform of the bunk. The Maximum Security Strap #TLA7751…

view full answer...

Answer 7

Yes, the Blue Ox Hitch Receiver Immobilizer II #BX88224 that you referenced can be used while towing a small trailer as long as the hitch on the vehicle has a 2 inch opening. We have confirmed with Blue Ox that you can use this product in towing…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The first thing you'll need to flat tow your 2015 Chevy Malibu LS is a base plate kit like the Roadmaster part #RM-523178-5 that is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting,…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...