Keel Pads For Crossmember On a ShoreLander Boat Trailer

Question

Question:

I have a Shorelander trailer that I need to replace the Keel Pad on, and was looking at the Yates Pad #YR1203SY. The crossmember that I need to mount this on has a bend so the material would have to be more flexible than this pad I think. Do you have another product that will work better?

asked by: Dan M

0

Expert Reply:

The Blue # YR1203SB and Yellow # YR1203SY Yates Keel Pads are the only keel pads we carry. While they do have some play you may consider trimming some of the side material on the pads which will allow it flex a bit more.

expert reply by: Bud M

0

Answer 1

In order to install the CE Smith Keel Roller for Boat Trailers part #CE29505 on a trailer you will first need the Roller Shaft with Pal Nuts for Boat Trailer Rollers part #CE10727A. Then, all you need is a set of mounting brackets such as the CE…

view full answer...

Answer 2

There are some mounting holes started on the sides of the Yates Keel Pad #YR1203SB. You simply need to acquire mounting hardware from your local hardware or home improvement store to mount these on the crossmember of your boat trailer. Mounting…

view full answer...

Answer 3

If you check out the video I attached to this page you'll see a general guide for removing the screen of a roof vent in the the first minute of the video. This process is basically standard amoung trailer roof vents so this process will be…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Keel Pads For Crossmember On a ShoreLander Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching