Does the Prodigy P3 Use the Same Wiring Harness as the Original Prodigy Brake Controller?

Question

Question:

I am considering upgrading my Tekonsha Prodigy original model to a Prodigy P3. Can I plug the existing wiring harness directly into the P3?

asked by: Scott M

1

Helpful Expert Reply:

Yes, you can. The Tekonsha Prodigy P3 item # 90195 uses the same connector as the original Prodigy.

expert reply by: Jerred H

1

Answer 1

Yes, the Rollaway Hitch Protector, #RM-050, should be plenty heavy enough to work on your 37 foot motorhome and keep the hitch from dragging when you back into your driveway, as long as the dip you have is not so deep that it is bending the hitch…

view full answer...

Answer 2

The truck pulling to the left when braking indicates to me that it is braking harder on the left side when you apply the brakes. This could indicate that more voltage, possibly due to a short circuit is getting to that side. It could also mean that…

view full answer...

Answer 3

In order to clear the 2 inch lip in your compartment, you will need spacers for the 60" x 20" MORryde Sliding Tray for RV Cargo Compartment #MR44FR. MORryde does make a kit for exactly that though, so all you would need to do is add the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 12

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Does the Prodigy P3 Use the Same Wiring Harness as the Original Prodigy Brake Controller?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching