Correct Replacement Hub & Drum For Lippert 7,000 lb Trailer Axle & 8 on 6-1/2" Bolt Pattern

Question

Question:

need a replacement hub and drum for Lippert 7k axle can you help? 8 on 6-1/2" bolt pattern

asked by: Van

0

Expert Reply:

Sure can, and the correct replacement hub and drum for your trailer with a Lippert 7,000 lb axle and 8 on 6-1/2" bolt pattern is the following:

- Trailer Hub and Drum Assembly - 7,000-lb Axles # LC53UD

expert reply by: Kyle S

0

Answer 1

I reached out to Lippert and the correct hub and drum assembly for your Dutchman Voltage 3200 is the Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased #LC53UD. This hub has 1/2" diameter x 1-5/16"…

view full answer...

Answer 2

First thing you should do at this point is test the 4-way of the wiring harness with a circuit tester part #PTW2993 for voltage on all of the right pins when the taillight signals are being applied. Just like in the video I attached. If the voltage…

view full answer...

Answer 3

The blue wire coming from the brake controller to the trailer brakes is the brake power output wire used to tell the trailer to apply the brakes once given the response from the brake controller. Therefore, you should not have a constant charge to…

view full answer...

Answer 4

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 5

The Optronics license plate light #UL94CB is sealed so you cannot change the bulb. The bulb that is used is a long-lasting heavy duty bulb but you cannot access it. We do have other license plate lights that might work for you. I have linked the…

view full answer...

Answer 6

The license plate lights should not have anything to do with your fuse blowing or your stop lights. Most likely there is a short blowing your fuse. If you don't locate and repair the short, you will continue to blow up fuses. You'll need to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Correct Replacement Hub & Drum For Lippert 7,000 lb Trailer Axle & 8 on 6-1/2" Bolt Pattern

Product Page this Question was Asked From

Continue Researching