Replacement Wheels for 4-Star LQ Horse Trailer With 235/85-16 Tires

Question

Question:

I am looking for new rims for my 4 STAR LQ horse trailer. The Tires are 235 85 16 rims are 8 lug. I can haul up to 2 horses, so about 2200#. I currently have chrome simulator hub caps that ate just annoying and I would like to have a chrome type rim that would look good on the trailer. No painted steel. My questionis - what else do I need to know to replace these rims appropriately? width of rim? acceptable hauling weight of rim? Please educate me on this and offer your advice. Thank you.

asked by: Trudy L

0

Expert Reply:

Rim width isn't likely a concern since most 235/85-16 tires will fit a variety of trailer wheel widths. For example, the # AM10295 fits 16" x 6", 16" x 6-1/2", 16" x 7", and 16" x 7-1/2" rims. The GVWR of the trailer is nice to know so you can make sure the wheel capacity is enough to handle the trailer and whatever it is carrying.

We have a few different wheels that could work for your application. If you aren't against powder coat you could use the Dexstar Steel Mini Mod Trailer Wheel # AM20794. This steel wheel has a capacity of 3,960 lbs. To be clear, wheel capacity is per wheel so if you had two of these it would be 7,920 lbs.

If powder coat falls under your desire to avoid paint then I recommend the Aluminum Modular Trailer Wheel # LHJM513. These have an aluminum construction so they carry a higher price but you won't have to worry about the coating getting scratched off or corrosion. They're technically silver but fairly polished which is close to chrome and would look good on any trailer. They also have a 3,750 lb capacity. If you want a nice finished look you can add the Lionshead Trailer Wheel Center Cap # LHCS109-SI60C as well.

expert reply by: Robin H

0

Answer 1

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 9

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 10

The spindle dimensions are as follows: A is the mounting dimension, B is the seal dimension, C is the inner bearing surface, D is the outer bearing surface and E is the diameter of the threaded portion of the spindle for spindle nut selection. Say…

view full answer...

Answer 11

Hi Kat, The rubber bumpers that we offer are all 96" in length but can come in different widths. Based on the dimensions you provided i your pictures the #D3-96 is going to be the best fit, but you will have to cut it down to size.

view full answer...

Replacement Wheels for 4-Star LQ Horse Trailer With 235/85-16 Tires

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching