Distance From Hitch Pin Hole to Sleeve of Hitch Extender e68YR

Question

Question:

What is the distance from the hitch side hole to the sleeve?

asked by: Peter

0

Expert Reply:

The distance from the hitch pin hole to the sleeve is 2 inches for the Trailer Hitch Extender for 1-1/4" Trailer Hitch Receivers - 7" Long # e68YR.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You would need to take one measurement to determine if the hitch adapter part #e93YR would fit your 2010 Honda Civic. You would need to measure from the center of your hitch pin hole out to the outer edge of your bumper. If that dimension is less…

view full answer...

Answer 3

Here is a list of the different bulb and socket kits we currently offer. Roadmaster Tail Light Wiring Kit with Bulbs #RM-155 Blue Ox Tail Light Wiring Kit - Bulb and Socket #BX8869 Roadmaster Tail Light Wiring Kit w/ 7-Way to 6-Wire Connector - LED…

view full answer...

Answer 4

The Trailer Hitch Adapter #e93YR is the closest extender/riser to the Trailer Hitch Extender #e68YR you found. The adapter does change from the 1-1/4" receiver to a 2" receiver for the accessory. You would need the Reducer #e63YR to get…

view full answer...

Answer 5

Based on the picture that you sent in, it looks like the top part of the shank attaches to the bike rack and the bottom portion, the part you are holding, looks like it is 1-1/4 inches and inserts into your hitch. You can find the size of your shank…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver #C11431 is designed for and confirmed to fit the Hatchback ST. There will be drilling required for installation, exhaust must be temporarily lowered for installation and access holes may need to be enlarged by…

view full answer...

Answer 7

Hey Robert, that's not a good sign but hopefully it's an easy fix. It sounds like maybe the connectors of the Curt trailer wiring harness part #C57ER are not seated properly which is causing the blinker malfunction. Usually a hyper flash is…

view full answer...

Answer 8

There have not been any major changes to the Stay-In-Play system since 2016, so I believe it certainly would be worthwhile (and a $$$ saver) to remove the major parts from the now-wrecked car. Provided you can get that done for a reasonable cost.…

view full answer...

Answer 9

You are on the right track. The only way we have that will allow you to use the Thule T2 Pro Xtr Bike Platform Rack part #TH69TX with the 2.5" receiver tube opening on your truck would be with adapter. For this, I recommend the Brophy Hitch…

view full answer...

Answer 10

I recommend the Roadmaster Dual Hitch Receiver Adapter, 10" Drop/Rise item #RM-077-10. This adapter was designed for this type of set up. Your Jeep Rubicon and Swagman E bike rack weigh well below the 10,000 lbs maximum capacity of this hitch. I…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The Draw-Tite Front Mount Trailer Hitch Receiver #65076 will fit your 2023 Ford F-350 dually. It features a bolt-on installation and has a 2" receiver. The hitch has a 9,000 lb line pull, 500 lb vertical load, and 5,000 lb gross trailer weight.…

view full answer...

Distance From Hitch Pin Hole to Sleeve of Hitch Extender e68YR

Product Page this Question was Asked From

Continue Researching