How to Determine Replacement Axle

Question

Question:

Hi there, I have a 2019 Parkliner trailer that needs a new axle and a new door. Can you please let me know what products you sell that would fit? Thanks

asked by: Sam

0

Expert Reply:

While we won't have doors, we may have a replacement axle for your trailer, but have no way of knowing what axle fits any specific trailer. So you'll have to do some measuring, as you will need to know the dimensions of your current axle's hub face to hub face and spring center to spring center; I have added a link below to a video which walks you through how to measure. The other thing you need to know is the weight capacity of the axle you need, which should match or exceed the GVWR of your trailer.

For example, Trailer Axle with Idler Hubs # e52GR has a 3,500 lb capacity and measures 95 inches from hub face to hub face and 80 inches from spring center to spring center.

I've added a link below to our selection of axles for you which you can filter through by length.

expert reply by: Kyle S

0

Answer 1

We carry 5 lug bolt pattern hubs, but none that would fit the same spindle as the part #8-213-5UC1 that you referenced. Since you said it's for a mobile home axle I can tell you right now we don't have anything that would fit. Mobile home…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

How to Determine Replacement Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching