Replacement For Wheel Center Cap SUSUC-60-BLK On Grand Design Solitude 345GK

Question

Question:

Im looking for this part. SUSUC-60-BLK. All I can find on your site is a chrome version. My 5wheel has black GD Solitude 345GK. Is the black one available?

asked by: Michael D

0

Expert Reply:

We will only have the Chrome # LHSI60C replacement version of the SUSUC-60-BLK. We do have the Americana Center Cap # AM90081 in black. This is slightly smaller but may still fit your Grand Design Solitude 345GK. These caps fit a hole size of 1-7/8" versus the 1-15/16" the Chrome # LHSI60C center cap is designed to fit.

expert reply by: Bud M

0

Answer 1

Snap-In Plug for Lionshead Trailer Wheel Center Caps #LHSI60C measures 2.17 inches in overall diameter and from the outside of one tab to the outside of the opposite tab is 1.92 inches. I have included a picture showing this. This cap was designed…

view full answer...

Answer 2

A 4,400 pound Lippert axle has a 6 on 5/12 bolt pattern and uses bearings #L44649 and #LM67048. So a good replacement hub that includes a bearing kit is part #8-407-5UC3-EZ.

view full answer...

Answer 3

You need Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2, part #8-407-5UC3-EZ. This is the hub comes with the bearings, races, and seals. The drum that is compatible is the Dexter Electric Brake Assembly for…

view full answer...

Answer 4

Since you have a Lippert 4,400 lb axle the correct replacement hub would be the part #8-407-5UC3-EZ that you referenced. Then for bearings you are correct you'd just need the part #L68149 and #LM67048. As far as the races go this hub uses the…

view full answer...

Answer 5

Pete, yes the Snap-In Plug for Lionshead Trailer Wheel Center Cap #LHSI60C are definitely not brittle and are better made than most. This is still made of plastic, has a chrome finish, and will work with 15" to 16" diameter wheels with a 6…

view full answer...

Answer 6

I have a hub solution for you. Even though we do carry a hub that is compatible with you current 4.4k axle that uses an inner bearing #L68149 and an outer bearing #LM67048, we do only carry one that has the brake drums. That is the Trailer Hub and…

view full answer...

Answer 7

The correct grease seals and bearings for the Dexter 8437302 is as follows: Inner bearing #L68149 Outer bearing #LM67048 Grease seal #RG06-050 For replacement hub we have the #8-407-5UC3-EZ which includes all of the above components so you do not…

view full answer...

Answer 8

Thanks for the picture! Your the 4400lb Dexter Axle on your 2021 Keystone Half-Ton Travel Trailer uses the following replacement parts: Inner bearing #L68149 Outer bearing #LM67048 Grease seal #RG06-050 For replacement hub we have the #8-407-5UC3-EZ…

view full answer...

Answer 9

The 4.4K axle uses a fairly unique bearing set, so you'll want to check the reference numbers on your inner and outer wheel bearings to ensure the replacement hub uses the same wheel bearings. If your current hubs use a LM67048 inner and a L44649…

view full answer...

Answer 10

Unfortunately, we do not sell our trailer hubs in pairs. You can only get the Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2, part #8-407-5UC3-EZ, individually.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...