Bearing and Seal for 2016 Jayco Jayfeather Ultra Light Hybrid X20E

Question

Question:

I have a 2016 Jayco Jay Feather Ultra-light hybrid X20E. Im looking for wheel bearing seals but my trailer is not listed. It has a Dexter 122967939 axle on it. Im not sure of the axle capacity. Any thoughts on what would fit? Thanks

asked by: Thaddeus W

0

Expert Reply:

I checked with Dexter and the correct bearings you need are the part # L44649 for the inner and outer bearing and for the seal # 10-9.

expert reply by: Jameson C

0

Answer 1

We have the Grease Seal for your Dexter 3,500lb axle as an Individual #58846 or Pair #RG06-050. These are double lip seals which are less likely to become damaged and leak out grease or let water in compared to other single lip grease seals.

view full answer...

Answer 2

For your 2020 Ford F-150 XLT the best front mount hitch is the Curt #C31083 because it's going to sit just a tad higher than the Draw-Tite alternative for better ground clearance. The 2" receiver for the Curt hitch will actually…

view full answer...

Answer 3

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 8

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 9

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 10

Hey Dave, what you gave me is enough info to get you replacement bearings. The grease seal 471750 matches the part #TMK48ZR. For a Timken replacement for the L44610 part number you'd need #TMK63VR. Then for a bearing for the L44649 you'd want…

view full answer...

Answer 11

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 12

The only difference between the #RG06-050 and Timken #TMK58ZR is the brand and quantity. Timken is typically considered to be a high quality brand, particularly for their USA made bearings. The #RG06-050 comes with two seals so it is the better…

view full answer...

Bearing and Seal for 2016 Jayco Jayfeather Ultra Light Hybrid X20E

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching