Correct Replacement Master Cylinder For a Titan Model 60 Actuator for Disc Brakes

Question

Question:

I have a Titan 60zx7000… I went to order a new master cylinder but now I realize I have the master for drum brakes in there. I have disc brakes. Is there a disc brake master that I can replace the old one with? Thank you

asked by: Jonny M

0

Expert Reply:

Yes, for your Titan Model 60 actuator, you can use the Replacement Master Cylinder Assembly for Dexter Model 60 Brake Actuators # T4820000 for a replacement.

This is going to be the correct master cylinder for disc brakes and will include everything you need for install.

expert reply by: Bryce D

0

Answer 1

The Replacement Master Cylinder Assembly #T4395100 that you referenced is only designed to work with drum brakes. For an Aero 6000 master cylinder kit the part #T4714200042 will work with disc brakes but you would need to reuse the other parts.

view full answer...

Answer 2

The Titan 60ZX7000 brake actuator is a Model 60 actuator, and you do have the correct part for a replacement master cylinder: - Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100 So this will work…

view full answer...

Answer 3

You are correct that the Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100 you were looking at is the replacement master cylinder for your older 23361. I included a video of the Titan #T4395100 for…

view full answer...

Answer 4

The actuator that you have referenced, #T47154007K, does not have a reverse lockout. However, if you were to add one using #T4748800, it works by blocking the flow of fluid back to the brakes when the tow vehicle is placed in reverse. There is no…

view full answer...

Answer 5

There are both drum and disc brake versions of the Titan Model 60 brake actuator available and you'll know what you have based on whether or not your trailer has drum or disc brakes. Disc brakes require higher pressure on the brake lines to…

view full answer...

Answer 6

We don't carry the A-60 actuators, but we do carry actuators that are confirmed to work on disc brakes. To see all of them check out the link I attached to the right. You will want to select the weight capacity and ball size you need from the…

view full answer...

Answer 7

90-95 ft lbs of torque is probably about right for your trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher.

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...