How Does Factory Jounce Bumper of 2021 Chevy Silverado 1500 Remove for Install of Timbren

Question

Question:

how does the original bumpers come off a 2021 silverado 1500 to put the new on dont see a bolt head up in the rubber

asked by: Frank

0

Expert Reply:

There is a bolt head in the center of the factory jounce bumper of your 2021 Chevy Silverado 1500 that you will need to remove to remove the factory jounce bumper. You can see this in the attached install video for the Timbren kit part # T28MR.

expert reply by: Jameson C

0

Answer 1

For your 2022 Chevy Silverado 1500 LTD Trailboss you can either use the SumoSprings #SS65FR which is rated for 1,000 lbs or the SumoSprings #SS45FR which are rated for 1,500 lbs. I honestly just recommend going with the higher rating. SumoSprings is…

view full answer...

Answer 2

I checked with Sumosprings and the #SS65FR and the dimensions are 5 inches tall by 4 inches in diameter without the spacer.

view full answer...

Answer 3

I reached out to my contact at SuperSprings to determine the best helper spring for your 2021 Trailboss truck. You were comparing the SuperSprings #SS45FR with the SuperSprings #SS65FR. These helper springs will have about a 1" gap before they…

view full answer...

Answer 4

The SumoSprings Solo Custom Helper Springs item #SS65FR are designed to do exactly what you talked about. These springs have progressive load control that compress according to the weight of your cargo. This will eliminate the sag you get in your…

view full answer...

Answer 5

When the SumoSprings Solo Custom Helper Springs item #SS65FR are installed on your 2020 GMC Sierra 1500 you will have a 1/2" - 1" of clearance with no additional cargo weight. This allows for you to have a comfortable ride when you are…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 8

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...