Does Reese Fifth Wheel Rail Kit RP50054-58 Work with Reese Round Tube Slider Hitch

Question

Question:

RP50054-58 will accommodate a 16k Reese, round tube slider correct? Manufactured in 2008. And is the measurement 26-1/4inch from back edge of bed to rear edge of rear rail? 2015 Ram 2500, 64inch bed

asked by: Jared

0

Expert Reply:

Yes, the Reese fifth wheel install rail kit part # RP50054-58 does work with a Reese round tube slider hitch like you have.

expert reply by: Jameson C

0

Answer 1

The measurements needed to install 5th wheel base rails in the bed of your 2015 Ram 2500 with a 6 Foot Bed will be different depending on the manufacturer and model base rails. Manufacturers call for different types of installations and use different…

view full answer...

Answer 2

Yes, 26-1/4 inches is the correct distance from rear edge of the truck bed to the rear edge of the rear rail of the Reese fifth wheel rail kit part #RP50054-58 that fits your 2020 Ram 2500. 28-3/16 inch is for the long bed trucks.

view full answer...

Answer 3

On a 2016 Ram 2500 short bed that does NOT have the factory 5th wheel prep package and using Reese custom installation kit #RP50054-58 the measurement from the rear edge of the tailgate to the back of the rear rail will be 26-1/4 inches. But this…

view full answer...

Answer 4

For your 2017 Ram 2500 the rail kit you would want is the Reese kit part #RP50054-58 which is a confirmed custom fit option that is also compatible with the Reese 20k fifth wheel hitch you have. I attached an install video for this kit for you to…

view full answer...

Answer 5

I can help you out with this installation. For 5th wheel install kit #RP50054-58 measure from the rear edge of the truck bed forward 28-3/16 inches for a long bed or 26-1/4 inches for a short bed. This is where the back edge of the rear rail will be.…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Does Reese Fifth Wheel Rail Kit RP50054-58 Work with Reese Round Tube Slider Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching