Recommended Bearings and Grease Seals for a Dexter 8,000 lbs Axle

Question

Question:

Trying to figue out what seals and bearing i need for my dexter 8,000 axels. Axel #132288021 Model D80

asked by: Bruce H

0

Expert Reply:

For a Dexter 8,000 lbs axle you will need the following parts:

Inner Bearing item # 25580

Outer Bearing item # 02475

Grease Seal item # GS-2125DL (2.125")

Grease Seal item # GS-2250DL (2.250")

We do not sell these parts in a kit. You will need one of each per hub.

expert reply by: Jerred H

0

Answer 1

According to the installation instructions from Dexter Axle the torque specs for the wet bolts on their Dexter E-Z Flex Suspension Kits, like part #K71-653-00, is 30 - 50 ft-lbs. I have attached a clip from their instructions for you to check out.

view full answer...

Answer 2

From what I could find online it looks like the Lippert 8K axles use inner bearing #25580, outer bearing #02475, and a grease seal that has an inner diameter of 2.250". If you are using a Kodiak disc brake kit like part #K2HR712D for 7K axles…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Answer 7

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

I understand your worry Tom, and I have a couple recommendations. First is the MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR which has a height of 4-1/2" for the mounting bolts. This is also 6-1/2" in width like the shorter…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Recommended Bearings and Grease Seals for a Dexter 8,000 lbs Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching