What Cut Out Dimension Does Optronics Trailer Taillight # ST70RB Fit

Question

Question:

So I’m in need of a trailer light that will fit a 2 3/4 x 6 3/4 opening Will this light work? Or can you offer a light that will fit this opening? The light that is in there has a 3 prong setup. The brake light has burned out

asked by: Harry

0

Expert Reply:

The Optronics trailer taillight part # ST70RB was designed to fit a 6-3/4 inch by 2-3/4 inch cut out using the grommet part # A70GB.

expert reply by: Jameson C

0

Answer 1

The ribs of the PVC Grommet for 6-1/2" Oval Trailer Tail Lights #a70gb do push further into the light assembly when you attempt to install on a thicker mounting surface. Since the ribs are on the top and bottom you'd just need to open the…

view full answer...

Answer 2

The #A70GB grommet is meant to fit a 6-11/16 by 2-5/8 inch rough opening. The maximum panel thickness would be right about 3/16 of an inch.

view full answer...

Answer 3

I went out into our warehouse and measured one of our Rubber Grommet for 6-1/2 inch Oval Trailer Light, #A70GB, that we have in stock. From the measurements I took, you will have to cut a hole that is 6-11/16 inches long and 2-5/8 inches tall.

view full answer...

Answer 4

I took a few measurements for you that I think will help. I have attached a diagram and made a short video for you showing the dimensions and the light. I believe this light will work with your bumper without having to cut out a hole in the back of…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

What Cut Out Dimension Does Optronics Trailer Taillight # ST70RB Fit

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching