What Parts are Needed To Convert Dometic Manual Awning to Electric On 2008 Eclipse Attitude 26FSAK?

Question

Question:

Im looking for a rv manual awning to electric conversion for an AandE Systems by Dometic awning. its on a 2008 Eclipse Attitude 26FSAK toyhauler. Do you have a conversion kit? If not, do you know if one is even available?

asked by: Shea W

1

Helpful Expert Reply:

You will need the Solera 12V Electric RV Awning Conversion Kit in Black # LC434723 or White # LC434724. These kits include new awning arms, along with caps to attach to your Dometic awning tube. You will need to run wiring to power the switch and then to the front awning arm.

expert reply by: Bud M

1

Answer 1

To convert your Dometic manual awning to a power unit, you can use the Solera 12V Conversion Kit in Black #LC434723 or White #LC434724 if you have a manual crank system. These Solera kits are compatible with Dometic (A&E) awnings like what you…

view full answer...

Answer 2

The Solera Manual Pull Style to Power Awning Conversion Kit, White #LC329250 is a nice upgrade. I've attached some photos of the installation instructions for the parts exchange and the wiring of the unit.

view full answer...

Answer 3

You can use this #LC329250 conversion kit if you have a pull style manual awning. These Solera Kits are compatible with your Dometic awnings and everything you need is included with the kit. I've provided a video for you to check out!

view full answer...

Answer 4

You will continue to use your awning's current arms when using the conversion kit: - Solera Manual Pull Style to Power Awning Conversion Kit #LC329250

view full answer...

Answer 5

When it comes to converting your pull style awing to an electric awning The Solera Manual Pull Style to Power Awning Conversion Kit, White #LC329250 will work. This kit is easy to install and can be used on a short, flat or pitched Solera awning. I…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...