Recommended Self-Tapping Screws For Thin Line Series Trailer Clearance and Side Marker Lights

Question

Question:

Hello, Can you please recommend a self tapping screw that will work with the A65PB LED bracket? The screws I have, the head is too tall and doesnt allow the LED to snap in place. Thank you!

asked by: Shane R

0

Expert Reply:

To mount the Thin Line Series Trailer Clearance and Side Marker Lights # A66PB you can use #10 truss head self-tapping screws from your local hardware store. Getting a 1-1/4" length should be more than enough to secure it to whatever you're wanting to.

expert reply by: Kevin C

0

Answer 1

It's a wire color difference but not a function difference on the pins of the 7-way. The difference comes from the fact that the two different styles are representative of two different areas that uses trailers. Traditional is usually seen on…

view full answer...

Answer 2

The blue wire on a trailer is typically the output wire to the electric brake assemblies. If this is the case on your trailer then the wire should only have power when you are hooked up to the tow vehicle and are applying the brakes, either by…

view full answer...

Answer 3

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...