Bearing Kit for 2004 Ranger Boat Trailer

Question

Question:

I have a 2004 Ranger Boats trailer tandem axle. I need to replace seal, o rings and bearings with race. Called Ranger parts and they referred me to trailer. If I could have parts #s I would like to order from you. Thanks!

asked by: Steve W

1

Helpful Expert Reply:

The Bearing Kit # BK2-100 will contain the new bearings, races, grease seal, tang washer and cotter pin for replacing the bearings on your 2004 Ranger Boat Trailer.

If you happened to have an oil bath hub the seal you would need is the # XLPROLUBE1980SEAL.

expert reply by: Jameson C

1

Answer 1

Based on the info you listed sounds like you would want the bearing kit part #BK1-150 which comes with the bearings, races, and seal for the hub you have.

view full answer...

Answer 2

The correct replacement grease seal for the AD2527E you listed is the part #168233.

view full answer...

Answer 3

Generally speaking, there is no need to apply a gasket maker on the outside of a grease seal prior to installing it in the hub. This is not really common practice nor have I ever seen any issues not doing so. That said, I am aware there are certain…

view full answer...

Answer 4

I believe you are referring to the manual for various Dexter hub assemblies that call for the application of Permatex sealant or equivalent prior to the installation of a new seal. While I don't recommend going against the…

view full answer...

Answer 5

To determine the correct replacement bearings, races and seals for the oil bath cool hubs on your Ranger Boat Trailer you will want to remove one of the hub assemblies so that you can take note of the part numbers on the existing components. If you…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 12

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Bearing Kit for 2004 Ranger Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching