Bearing Kit for 2017 Ranger Trailer with Bearings L44649

Question

Question:

Hoping you can help I have already contacted Ranger and Dexter which was unable to provide the information. I have a 2017 Ranger trailer dual axe with Vault hub system currently no problems. However as I am planning some trips this summer I wanted to pick up some spare parts for the hub system. Could you please verify if these are the correct parts? Photo of trailer information included. Axle Inner Outer Load Capacity Cone Cup Cone Cup 1500# -2500# L44649 L44610 L44649 L44610 Seal Description Trailer Buddy NOK CR National 198-138-SP1-1 07026 AB1990EO 13557 482163N

asked by: Glen Y

0

Expert Reply:

Based on the info you listed sounds like you would want the bearing kit part # BK1-150 which comes with the bearings, races, and seal for the hub you have.

expert reply by: Jameson C

0

Answer 1

I was able to find the seal on your trailer in my research. The seal that comes in the bearing kit #BK2-100 has different inner and outer diameters that the existing seal on your trailer. The inner and outer diameters of your seal are not common,…

view full answer...

Answer 2

We're not sure what the O stands for, in anything, but to make sure this bearing seal works for you you can take a few quick measurements. You will need to measure the outside diameter of your existing seal, or the inside diameter of the…

view full answer...

Answer 3

We can help you find the seal you need, but the part number you mentioned does not match anything we offer. Can you get me the inner and outer diameters of the seal? With that I can see what we have that matches.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 11

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as…

view full answer...

Answer 12

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub…

view full answer...

Bearing Kit for 2017 Ranger Trailer with Bearings L44649

Product Page this Question was Asked From

Continue Researching