Availability of Trailer Axle with Close to 60 inch Spring Seat to Spring Seat Dimension

Question

Question:

Hello - im looking for a axle, with a spring center length of about 60 give or take an inch or two. Hub face length is not a critical measurement. Do you carry anything with that dimension? thanks again,

asked by: Clay V

0

Expert Reply:

We have 2,000 lb axles like the etrailer part # e32GR that have a spring seat measurement that is similar to what you are looking for. This has that dimension at 58 inches and has a hub face to hub face dimension of 72 inches.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 12

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...