What Is The Spacing Required Between Two Base Rails

Question

Question:

I don’t have a instruction sheet but what’s the gap between first and second rail on my 2002 dodge 6 1/2’bed ?

asked by: Jerry

0

Expert Reply:

You should have 22" from center to center of the rails (pictured below) in your kit # C16200. I typically get the first rail installed and then drop the hitch I plan on using into the first rail and use it to help set the second rail in place and keep it from moving around while I'm drilling the initial holes in the bed.

expert reply by: Kevin C

0

ISR Rail Spacing
(click to enlarge)

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 4

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 5

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 6

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 7

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 8

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 9

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 10

It sounds like you could have a set of standard fifth wheel rails that most manufacturers use for their fifth wheel hitches to install into. The different manufacturers all make their own brand of rail kit, but they all have basically the same…

view full answer...

Answer 11

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

What Is The Spacing Required Between Two Base Rails

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching