Dimensions Of The Bulldog Powered Trailer Jack # BD500199

Question

Question:

Can you send the dimensions of the bulldog 500199? Trying to see if I can mount it forwards and still open my tailgate. I have the lippert smart jack now

asked by: Brandon S

0

Expert Reply:

The top of the motor housing on the Bulldog Powered Drive Trailer Jack # BD500199 is approximately 21-1/4" tall from the top of the mounting flange. From the center of the tube forward to the edge of the housing is approximately 4".

expert reply by: Kevin C

0

Dimensions
(click to enlarge)

Answer 1

The Stromberg Carlson Electric Trailer Jack #JET-3555 has the larger outer tube diameter as you mentioned. I recommend using a rotary tool like a Dremal to enlarge that hole. Another great option is the Bulldog Powered Drive Trailer Jack- 22"…

view full answer...

Answer 2

I went out to our warehouse to assist with the dimensions of the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 4,000 lbs - Black #BD500199. From the top of the mounting plate to the bottom of the motor housing is 12-7/8…

view full answer...

Answer 3

Yes, the Bulldog Powered Drive Trailer Jack - Black #BD500199 can be wired to either a battery or to the 7-way. If you wire it to the battery you'll be able to operate the jack any time, as long as the battery has a 12v charge. If you wire it to…

view full answer...

Answer 4

Your picture didn't make it through and I am not sure what product you are interested in.

view full answer...

Answer 5

When we installed the Bulldog Powered Drive Trailer Jack #BD500199 on the utility trailer we ran the power wire to the 7-way junction box. When demonstrating the jack the 7-way was plugged into a 12 volt power source similar to the power that will…

view full answer...

Answer 6

The lowest profile A-Frame Trailer Jack we currently carry is the Bulldog Powered Drive Trailer Jack #BD500187 which has a 20-1/2" height from the mounting plate to the top of the jack. That being said you do still need to consider the weight…

view full answer...

Answer 7

Sorry Jennifer, I am a bit confused as you were looking at the Replacement U-Clamp Bracket #RM-B141 which mounts with bolts and not U-bolts. This part works with the Split Bushing #RM-205217-10 for the discontinued Roadmaster Front Anti-Sway Bar…

view full answer...

Answer 8

As you have a Coleman Mach system currently you can use the Furrion Chill AC units from the list below. These will simply replace only the rooftop units and the controls and thermostats you currently have in place with control the new AC's. 13.5K…

view full answer...

Answer 9

Hi Joe, The Blue Ox Base Plate Kit #BX1139 is a confirmed fit for your 2024 Jeep Wrangler Rubicon X per Blue Ox. I don't currently have an installation video on a model with a steel bumper but I did measure from the mounting holes down to the…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Brien, it sounds like you did your research so kudos to you, but the awning you're looking at is not going to work with the wind sensor. You'd need to use the Solera Smart Arm 12V Power RV Awning #LC517517 instead. You're also going to…

view full answer...

Answer 12

Hey Johnny, There unfortunately isn't a guide to tell us the correct awning needed for your trailer so we'll need to get a measurement first to determine the best fit. I'm assuming you're replacing a different awning and not adding…

view full answer...

Dimensions Of The Bulldog Powered Trailer Jack # BD500199

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching