Shortest Profile Electric Tongue Jack Available For Hatchback Door Clearance

Question

Question:

What are the lowest profile/height electric tongue jacks available? My vehicle hatchback is blocked from opening by my current jack.

asked by: Sean H

0

Expert Reply:

The lowest profile A-Frame Trailer Jack we currently carry is the Bulldog Powered Drive Trailer Jack # BD500187 which has a 20-1/2" height from the mounting plate to the top of the jack.

That being said you do still need to consider the weight capacity of the jack if you can provide me with the weight capacity of your current jack or the GVWR of your trailer I can find the shortest option in that weight class.

expert reply by: Kevin C

0

Bluudog Trailer Jack Height
(click to enlarge)

Answer 1

As long as the 7-way on your 2011 Toyota Tundra has the 12 volt circuit active and you wire the #BD500200 to the 12 volt circuit on your trailer 7-way (the 9:00 pin), the jack would work. It's typically preferred to power the jack off of a…

view full answer...

Answer 2

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 5

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 8

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 9

Your 2008 Chevy HHR should have a set of rails on the roof that run from front to back. Which means we have the Rhino Rack part numbers #RRVA106B-2 and #RRSX100 as a confirmed fit, but the kit you mentioned is not a fit.

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Slipper Springs like #e33SR do not use a bolt and bushing for the open eye end of the spring. It connects directly to the hanger using a slipper spring hanger kit.

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...