Suspension Lift Kit Options For a 2022 7' x 14' Continental Enclosed Cargo Trailer

Question

Question:

I have a 7x14 - 2022 - Continental Cargo Enclosed Trailer - Vulcan series with tandem axles I am looking to gain some extra ground clearance and wanted to inquire about any flip kits or other options to accomplish this.

asked by: Brad

0

Expert Reply:

Based on the information I could find on your 7x14 Continental Vulcan series enclosed cargo trailer I do see it does use a leaf spring suspension with 3,500lb axles. If your axles are placed on top of the leaf springs you can use the Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00 to mount each axle under the leaf springs. This will give you a rise of around 3-4" depending on the height of your leaf springs.

Another option is the Correct Track Trailer Alignment and Lift Kit # RR23QX which is designed for double eye spring suspension. This will allow you to raise the trailer 1-1/4" or 2-1/4" depending on your preference.

expert reply by: Bud M

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have so I…

view full answer...

Answer 4

Thanks for the pictures! Since your 2022 Grand Design Reflection 303RLS came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. It looks like you have the standard 3" wide frame hanger so all of the…

view full answer...

Answer 5

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 12

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Suspension Lift Kit Options For a 2022 7' x 14' Continental Enclosed Cargo Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching