single and Tandem Axle Brake Line Kit for a Dexter Hydraulic Trailer Brake Assembly

Question

Question:

Hi what brake line fitting is used to connect brake line to this brake plate?

asked by: Kun

0

Expert Reply:

For the Dexter Galphorite Free-Backing Hydraulic Trailer Brake Assembly # T4489600 you can use the Kodiak Hydraulic Brake Line Kit # 18SI-BLKIT for a single axle brake line kit or # 18TA-BLKIT for a tandem axle kit.

expert reply by: Bryce D

0

Answer 1

According to the manufacturer the Replacement Caliper for Titan 10" Brakes #K71-773-01 is rated for use with EOH systems. Since your current brake set up is causing damage to your rotors it may not be a bad idea to replace your brake set up. The…

view full answer...

Answer 2

The Kodiak Disc Brake Caliper 3,500 lbs to 6,000 lbs #KDBC225S and similar finishes will require the Kodiak Disc Brake Caliper Rebuild Kit for 3,500 lb to 6,000 lb Trailer Brakes #KDBC225KIT which will give you all the seals, bolts, bushings, and…

view full answer...

Answer 3

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 4

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

single and Tandem Axle Brake Line Kit for a Dexter Hydraulic Trailer Brake Assembly

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching