Could Curt Hitch # C13704 Fit 2022 East to West Tandara 321RL-OK

Question

Question:

I have a 2022 East to West Tandara 321RL-OK. Will this fit it? Its an I-beam.

asked by: Dustin K

0

Expert Reply:

The Curt hitch part # C13704 does fit I-beam frames like your 2022 East to West Tandara 321RL-OK has but the frame has to be between 22 and 66 inches measured from outside to outside. So it could work for you and most likely does but you would want to measure your frame first.

expert reply by: Jameson C

0

Answer 1

I went out to the warehouse and measured Curt trailer hitch #C13704 for you. The distance from the top of the mounting flanges to the top of the cross tube is 2 inches. I have included some pictures with additional measurements for you.

view full answer...

Answer 2

It's just a monitor setting that needs changed on the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision part #FOS05TASF, it does not mean there was an error during installation or with the trailer. I have attached for you below a…

view full answer...

Answer 3

To install the Curt hitch part #13571 the two bolt sizes needed are M12-1.25x40 and M10-1.25x35 which are included. If you need new bolts you can order them from us as part #RHK.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, if you plan on bolting the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR on then you would need to drill holes in the adjustable arms in order to set them to the correct length. There aren't any predrilled so that this one…

view full answer...

Answer 10

I have attached a few photos for you with all the dimensions we have for the Ark Drop Down Corner RV Stabilizer Jacks part #AR34FR. That said, Ark is an Australian company so the measurements are in metric, millimeter to be specific so you may need…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The Torflex Lift Kit #K71-707-02 may be exactly what you need for your Winnebago Micro Minnie 1706FB with tandem torsion axles but we do not have any database of axles and I was unable to find the specific axles on your trailer in my research. This…

view full answer...

Could Curt Hitch # C13704 Fit 2022 East to West Tandara 321RL-OK

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching