Length of Wheel Studs on Dexter Trailer Hub # K08-201-9B

Question

Question:

How long are the studs on this hub? I.e. How far to they protrude away from the hub face? Is there any variation between stud length on any of your 6x139.7mm hubs from different manufacturers? Or is their an industry standard length? Cheers

asked by: Thomas O

0

Expert Reply:

The Dexter Trailer Hub and Drum Assembly # K08-201-9B that you referenced has a stud length of 1-1/4 inches which is the standard length for trailer hubs like yours.

expert reply by: Jameson C

0

Answer 1

The Dexter Trailer Hub and Drum Assembly with Parking Brake - 6K Axles - 12" Diameter - 6 on 5-1/2 #K08-201-9B you were looking at actually only works with wheels ranging from 14-1/2" - 16" in diameter. This hub and drum…

view full answer...

Answer 2

There are a couple of versions of the Dexter Axle EZ-Lube hub and drum assemblies so you really just need to determine which one fits your application best. All 3 options you listed use the same bearings so it boils down to the weight capacity and…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 10

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Length of Wheel Studs on Dexter Trailer Hub # K08-201-9B

Product Page this Question was Asked From

Continue Researching