Bearing Buddy Fitment for a Malone MicroSport Trailer

Question

Question:

Hello, I am trying to determine which one is the correct size Bearing Buddy for a Malone Microsport Trailer with 12 wheels. I cannot determine if it is the 1968SS or the 1980. Id appreciate if you can guide me in the right direction. Thanks

asked by: Luis B

0

Expert Reply:

The Malone MicroSport trailers use a grease cap with a 1.98" outer diameter so you need the 1980 Bearing Buddy kit which comes in the following:

- Chrome # BB1980A
- Stainless Steel # BB1980A-SS

expert reply by: Jon G

0

Answer 1

The closest grease seal we have to what you're looking for is the Grease Seal part #10-9 which measures 1.500" I.D. x 1.987" O.D. It's commonly used on 2,700 lb axles.

view full answer...

Answer 2

No, it is not normal for seals to go bad that quickly. Typically if your hubs are spraying/leaking grease, it is because of a bad seal. From what I could find, it looks like your Malone Microsport trailer has a 1.98 inch diameter hub. The correct…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...