Replacement Controller and Touchpad For Lippert 10540 On a 2007 Damon Outlaw 3611 Class A RV

Question

Question:

I need to replace a Lippert 10540 touchpad automatic leveling controller. Do you have a product that will work. 2007 Damon Outlaw 3611 F53.

asked by: Jeffrey C

0

Expert Reply:

The Replacement Lippert Leveling Control Brain # LC53ED is the replacement for the 10540 controller. If you are needing the Control Panel # LC175225 we also have that available.

The Harness # LC178278 is needed to convert the 4-pin square connector on your old controller to the 4-pin rectangle connector on the new controller.

expert reply by: Bud M

0

Answer 1

It appears that all you going to need is the Replacement Lippert 4-Point Leveling System Control Brain Wiring Harness #LC178278. This wiring harness will allow you to plug your new Replacement Lippert Leveling Control Brain for 4-Point Leveling…

view full answer...

Answer 2

I believe you are referring to the Lippert Components High-Speed Power Stabilizer Jack part #LC369774 that comes with the white switch part #LC144214. Lippert was not able to provide me a wiring diagram for the white switch but was able to give me…

view full answer...

Answer 3

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Answer 4

I reached out to my contact at Lippert and he said that it sounds like you have an older Power Gear Manual Leveling kit that had the ground running from the solenoid to the control board. This new kit, part #LC359259, can be used as a replacement but…

view full answer...

Answer 5

The plug that includes the red wire from the Replacement Lippert Power Gear Manual Leveling Control Kit #LC359259 will plug into the back of the control panel and then the other end will plug into the connector coming off of the pump. The other…

view full answer...

Answer 6

The Ground Control 3.0 harness won't work for motorhome leveling system, but you did find the right replacement harness for the Lippert Control Panel with Amp Connector for 4-Point Leveling System #LC175225. We did confirm with the manufacturer,…

view full answer...

Answer 7

We do have what you need available. I was able to locate the LC175226 controller but it is no longer available. I contacted the manufacturer and they provided information for the correct replacement part. The correct replacement part is the…

view full answer...

Answer 8

The #LC53ED is the correct replacement control brain for the Lippert 4 point leveling system on your motorhome. It is essentially the same controller for ALL Lippert 4-point leveling systems. This leveling system is common on fifth wheels, but we…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...