Car Mounted Tow Bar for Use with Roadmaster Crossbar Base Plate 521876-1

Question

Question:

I just bought the 521876-1 mounting plate set up for my 2007 mini convertible I want a hitch ball type of tow bar for this. What is recommended?

asked by: Ron W

0

Expert Reply:

The Roadmaster Stowmaster tow bar part # RM-501 is a great choice for a tow bar that attaches to a hitch ball that is compatible with the Cross Bar base plate kit part # 521876-1 that fits your 2007 Mini.

expert reply by: Jameson C

0

Answer 1

If you haven't already check your owner's manual and make sure there aren't any restrictions preventing your 2006 Mini Cooper S from being able to be flat towed. The Roadmaster Base Plate Kit #521876-1 will fit your Mini as…

view full answer...

Answer 2

You'll simply slide the bare end of the wire into the quick connect and flip the orange lever down to lock the wire in place. The wiring diagram for the Progressive Dynamics Transfer Switch with Quick Flip Connectors - Plastic Case - 30 Amp…

view full answer...

Answer 3

For the 2005 Mini Cooper Convertible we have the Roadmaster base plate kit part #521876-1 as a confirmed fit. For an adapter to allow a Blue Ox Alpha #BX7380 tow bar to attach you need the part #RM-032. For lighting you can use the diode kit,…

view full answer...

Answer 4

You asked about Blue Ox products, but for your Mini the parts were not compatible to your tow vehicle. To flat tow your 2006 Mini Cooper Convertible S model (with standard transmission) you will first need Roadmaster #521876-1 base plates which are…

view full answer...

Answer 5

The crossbar of the Roadmaster Stowmaster #RM-501 stays attached to the removable arms of the base plate kit #521876-1 which you can leave attached and pull the arms out with the crossbar.

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Car Mounted Tow Bar for Use with Roadmaster Crossbar Base Plate 521876-1

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching